The obd port looks like the picture below This port is located somewhere under your drivers dash, lay on the floor and look up. In some cars, it may be behind a panel, but almost all cars will have this port. From this port, information such as fuel, mileage, and other information comes out via data. Most importantly, it has power and ground. Do you have a new teen driver in your family, do you want to track your car for security or other reasons? Track where your kids are, when they drive and if they are going too fast.
: Subwoofers: Electronics
You will want one that meets your specific needs for your specific vehicle. It needs to fit your vehicle, as well as your preferences. So take your time and select and item with care.
How to Hook Up a Subwoofer to a Home Stereo by Joe Fletcher. How to Wire 2 Subwoofers on a Mono Amplifier. How to Connect a Subwoofer to a Yamaha Receiver. Kirsch K3 Instructions. How to Troubleshoot a Klipsch Subwoofer. How to Hook Up Surround Sound to a .
Originally Posted by Trogdor Thanks dd3mon. Okay, how will imaging be effected by a sub in the corner? Has anyone done this with with 2 sub’s on placed in both front corners? I’m considering getting an external sub for my 2 channel setup. My speakers do bass quite nicely tight and accurate but not booming though I’m about to change amplification drastically.
Many sub manufacturers especially the cylindrical models such as SVS’s most popular line recommend corner placement. Imaging should be not be affected unless your mains are extremely bass-light so the sub’s crossover has to be set very high.
So what will we need to do this? But I doubt any of you guys will be using an amp that big. Walmart sells amplifier kits as do some other stores. The kits tell you how many watts they can handle. Add Tip Ask Question Step 2: Choosing an Amp and Speaker This can be a tricky step.
The subwoofer is an excellent add-on component to any stereo system. It provides the deep bass that most speakers lack and enhances both music and movie soundtracks. Whether you have a powered or passive sub, you’ll need to get it connected to your amplifier for it to work.
Did this video help you? Haaaaaaaaaaa go to school Dillon Mccray: If you do the big three wire upgrade on your car it helps alot just look up the big three upgrade on YouTube if you haven’t done it already CallMeDaddy III: So I could hook up 2 8ohm subs to a 4ohm amp? The amp is mono watt Max and the subs are 8 ohm w rms w max. I have 2 alpine type R 10 inch subs in a ported box rated at rms a piece. I just ordered a rockford fosgate prime amp which is 1 ohm 2 0hm 4 ohm what would be the best way to wire it to match my rms on my subs.
Hi, can I use 3 ohms subwoofer on 4ohms amplifier thanks.
how do I hook up two passive subwoofers
One thing I learned pretty early in life is that speakers are not meant to be wired together in a haphazard manner. In fact, whenever you plan to connect more than two speakers to a two-channel amplifier — or more than four speakers to a four-channel amp — there are a few things to consider, not the least of which is the amps ability to handle low-impedance loads. Ignoring the basics is like playing Russian roulette with your amplifier:
How to Hook Up 2 Speakers & a Subwoofer to a Pennsylvania Amp With Only 2 Outputs? Hooking up two speakers and a subwoofer to a Pennsylvania amp requires using one channel of the amp to power the two speakers and using the second channel to power the subwoofer. The trick is to use speakers with the correct impedance. The
You cannot have too much subwoofer. A bigger subwoofer from the same manufacturer will always play lower, has lower distortion, more headroom, and better long term reliability if played at the same listening level. Hence, if budget is not an issue, going for the larger sub will always be beneficial, if there is no WAF or physical limitations. We have suggested room sizes that each subwoofer is recommended for. This of course is a very rough guide. Very much depends on individual tastes.
We have customers who find four VTF H in a 1, cu. We also have customers who are happy with a STF-1 in a 5, cu. Hence we suggest going with the biggest subwoofer that your budget, spouse and space allows.
How to Hook Up Subwoofers to an Amp
How do you hook up a 3 farad capacitor to two amps? You also must know how use capacitors on the sub to make it respond only to bass! And while they do make commercially available accessories that do what Y-T-Y says, by the time you buy one that works for your situation, install it, etc. How do you hook up an amp?
· asuming the jbl is a powered sub you would need a y splitter 1 male to 2 female phonos and 2 phono leads. connect the y splitter into the sub out on the onkyo amp and then connect your 2 phono leads into the 2 females on the splitter and then connect the other 2 ends of the phonos into your ://
May 4th, Got a pimple, spray some Windex on it. Got a sore throat, swish some vinegar and honey. Eat some chicken soup. Home remedies, some are good, others are a mixed bag at best. I spent years conjuring up home remedies or tricks for properly calibrating multiple subwoofer theater rooms. In a perfectly rectangular room with the ability to place identical subs in the ideal locations around the room, this isn’t such a daunting task.
What happens if you hook up two subs to a mono channel amp
January 24, We are always preaching the more subs the better in a home theater system particularly two to four for a variety of reasons such as; smoother bass response across a wider listening area and increased dynamic range. So now that you’ve decided to purchase two or four subs, its time to show you how to connect them up properly to ensure you achieve the maximum benefits of a multi sub system.
This article has been recently updated to incorporate two YouTube video discussions – 1.
Buy Samsung HW-H Channel Sound Stand with Dual Built-In Subwoofers ( Model): Speakers – FREE DELIVERY possible on eligible purchases.
Even if you have high-end speakers and amplification, a subwoofer can add the deep bass that you may be missing. Connect using a line-out connection. This type of connection will send a nonamplified, low-frequency signal to your subwoofer. This is for powered subwoofers only subwoofers with built-in amplification that you plug into the power outlet. Turn the subwoofer “On” on your receiver or preamplifer menu. Connect using speaker-level connections.